Home » Produtos Estética » Whitepost System

Whitepost System

A system of intraradicular posts made of fiberglass composite and epoxy resin.

High mechanical strength.
Radiopacity (radiographic assessment)
Double tapered design;
Translucency (better esthetics);
Adhesive capacity (pre-silanized
surface).

Benefits

Double taper design:
Better adaptation to the canal without requiring further wear on the dental structure.

Esthetics and excellent translucency:
High esthetic capacity and excellent light conductivity, helping the light curing of the cement.

Radiopacity:
Possibility of radiographic diagnosis.

Exclusive drill:
Specific for each size of post, leading to a standardized root preparation.

High Safety:
Modulus of elasticity similar to dentin, reducing the risk of radicular fracture.

DC-E Version ( Special)(DC-E):
The DC-E version ( Special) has the same apical diameter as its corresponding DC version, but on the cervical third it shows a wider diameter that makes it the best choice for cases where there is less quantity of remaining coronal structure and for teeth with wide canals.

Recommendations

Restoration of endodontically treated tooth to assist in retention of the restorative material and distribute stresses imposed on the tooth.

Commercial Availability

Whitepost

• Packaging containing 05 posts of the same size.
Available in the sizes: DC 0.5, DC 1, DC 2 , DC 3.

Whitepost DC-E Refill

• Packaging containing 05 posts of the same size.
Available in the sizes: DCE 0.5, DCE 1, DCE 2.

Whitepost DC and DC-E Kit

• Kit containing the posts DC 0.5, DCE 0.5, DC 1, DCE 1, DCE 2
05 posts of each size (total of 25 posts), their respective drills, and a template for post selection.

Whitepost Intro DC Kit

• Packaging containing 05 posts of the same size and their respective drill. Available in the sizes: DC 0.5, DC 1, DC 2, DC 3.

Whitepost DC Kit

• Kit containing the posts DC 0.5, DC 1, DC 2, DC 3, DCE 2
05 posts of each size (total of 25 posts), their respective drills, and a template for post selection.

Step by step

Step 1 of 10

Take an X-ray (periapical radiography) and check the quality of the endodontics. Select the post according to the diameter of the canal, overlapping the template over the X-ray of the tooth.

Step 2 of 10

Insulate the operatory field. Prioritize the use of rubber dam.

Step 3 of 10

Remove the gutta percha from the canal using a suitable drill or instrument, keeping 3 to 5 mm of gutta percha in the apical region, ensuring the sealing of the endodontic filling.

Step 4 of 10

Prepare the root canal with appropriate drills until it matches the shape of the post. Avoid unnecessary wear.

Step 5 of 10

Trim the coronal excess from the post, if necessary, and put it back in position to check the fitting.

Step 6 of 10

Apply the phosphoric acid gel (Condac 37 – FGM) for 15 seconds inside the root canal and remaining dental structure. Wash thoroughly and remove the excess water with absorbent paper cones.

Step 7 of 10

Use the Cavibrush Long (FGM) for application of the dual-curing or light-curing adhesive system along the entire etched root canal.

Step 8 of 10

Clean the Whitepost with 70% alcohol, or Chlorhexidine at 2%. Apply Prosil Silane (FGM) on the entire surface of the post and wait for it to dry.

Step 9 of 10

With a lentulo drill, introduce the Allcem resin cement (FGM) inside the canal or use Allcem Core (FGM) with its applicator tip.

Step 10 of 10

Insert the post carefully in the canal and proceed with light-curing of the cement on the surface and through the post.