Home » Produtos Estética » Allcem Veneer APS

Allcem Veneer APS

Light-curing resin cement for cementation of ceramic veneers and no-prep veneers.

Predictability of results
Esthetic longevity
Fluorescence

Benefits

APS technology:
• Reduces or eliminates visual alteration of shade and opacity of the cement before/after photopolymerization.• Longer working time under ambient light.• Compatible with all blue light-emitting light-curing devices.

High shade stability:
Esthetic longevity.

Excellent viscosity:
Easy handling and application.

Radiopacity:
Possibilidade de diagnóstico radiográfico.

Fluorescência:
Possibility of radiographic diagnosis.

Fluorescence:
Appearance similar to the natural tooth.

Excellent mechanical properties:
Reliable and long-lasting cementation.

Recommendations

Adhesive of ceramic and composite restorations (made in the Office or in the laboratory) with a low layer thickness (up to 15 mm) that enables the use of a purely light-curing technique due to their high translucency.

Commercial Availability

Refill

• 1 syringe with 2.5g, available in shades A1, A2, A3, Trans, Opaque White and E-bleach M.

• 5 applicator tips.

Mini kit

• 3 Allcem Veneer with 2.5g in shades: A1, OW, Trans.
• 3 Allcem Veneer Try-in with 2g in shades: A1, OW, Trans.
• 1 Ambar APS with 2ml.
• Applicator tips.

Step by step

Step 1 of 14

Tooth preparation: Make sure the tooth surface and the prosthetic piece are free from Allcem Veneer Try-In (FGM) and/or any other substances.

Step 2 of 14

Make a relative or absolute isolation according to the professional preference, and according to the teeth that will be subjected to cementation of the pieces.

Step 3 of 14

If the cervical finish line is under the gum, and your preference is to use relative isolation, perform the retracting maneuver with the retraction cords.

Step 4 of 14

Etch the enamel surface and/or dentin with phosphoric acid Condac 37 (FGM), wash and gently dry without dehydrating it.

Step 5 of 14

Etch the enamel surface and/or dentin with phosphoric acid Condac 37 (FGM), wash and gently dry without dehydrating it.

Step 6 of 14

Preparation of the piece. Etch the internal surface of the veneer with fluoride acid Condac Porcelana 10% (FGM), for the required time, according to the porcelain

Step 7 of 14

Apply a layer of silane Prosil (FGM) into the piece and let it dry for 1 minute.

Step 8 of 14

Apply the adhesive into the piece, according to the manufacturer’s recommendation. Do not light

Step 9 of 14

Cementation. After preparing the piece and the tooth, perform the cementation as follows:

Step 10 of 14

Straight from the syringe, or using a spatula, apply a thin layer of cement under the internal face of the veneer.

Step 11 of 14

Position the piece in the preparation and, keeping it under slight pressure, remove excesses of cement using Cavibrush (FGM) or a probe.

Step 12 of 14

After removing the cement excesses, and prior to photoactivation, apply glycerin gel to the borders of the restoration to avoid the layer inhibited by oxygen. The light curing should be performed for 40 seconds* on each of the borders (mesial, distal and cervical) and directly on the vestibular face.

Step 13 of 14

Finishing and polishing may be performed with thin sandpaper disks Diamond Pro (FGM) and sandpaper strips, polishing pastes Diamond Excel (FGM) and felt disks Diamond Flex (FGM).

Step 14 of 14

*To photoactivate the material, use halogen light devices or LED with power equal to or higher than 450mW/cm2, and blue light issuing spectrum (400-500nm).

Step 1 of 14

Tooth preparation: Make sure the tooth surface and the prosthetic piece are free from Allcem Veneer Try-In (FGM) and/or any other substances.

Step 2 of 14

Make a relative or absolute isolation according to the professional preference, and according to the teeth that will be subjected to cementation of the pieces.

Step 3 of 14

If the cervical finish line is under the gum, and your preference is to use relative isolation, perform the retracting maneuver with the retraction cords.

Step 4 of 14

Etch the enamel surface and/or dentin with phosphoric acid Condac 37 (FGM), wash and gently dry without dehydrating it.

Step 5 of 14

Etch the enamel surface and/or dentin with phosphoric acid Condac 37 (FGM), wash and gently dry without dehydrating it.

Step 6 of 14

Preparation of the piece. Etch the internal surface of the veneer with fluoride acid Condac Porcelana 10% (FGM), for the required time, according to the porcelain

Step 7 of 14

Apply a layer of silane Prosil (FGM) into the piece and let it dry for 1 minute.

Step 8 of 14

Apply the adhesive into the piece, according to the manufacturer’s recommendation. Do not light

Step 9 of 14

Cementation. After preparing the piece and the tooth, perform the cementation as follows:

Step 10 of 14

Straight from the syringe, or using a spatula, apply a thin layer of cement under the internal face of the veneer.

Step 11 of 14

Position the piece in the preparation and, keeping it under slight pressure, remove excesses of cement using Cavibrush (FGM) or a probe.

Step 12 of 14

Step 13 of 14

Finishing and polishing may be performed with thin sandpaper disks Diamond Pro (FGM) and sandpaper strips, polishing pastes Diamond Excel (FGM) and felt disks Diamond Flex (FGM).

Step 14 of 14

*To photoactivate the material, use halogen light devices or LED with power equal to or higher than 450mW/cm2, and blue light issuing spectrum (400-500nm).